www.ams.com/AS5510
Revision 0.1
5 - 18
AS5510
Datasheet - Electrical Characteristics
6 Electrical Characteristics
6.1 DC Characteristics for Digital Inputs and Outputs
6.1.1 CMOS Input: ADR
Note: Operating conditions: T
amb
= -30癈 to +85癈, VDD = 2.5V to 3.6V (3V operation) unless otherwise noted.
6.1.2 CMOS I睠: SDA, SCL
Table 3. Operating Conditions
Symbol
Parameter
Conditions
Min
Typ
Max
Units
VDD
Supply voltage at pin VDD
2.5
3
3.6
V
I
supp
Supply current
@ 25癈 ambient temperature
3.5
mA
I
pd
Power down current
25
糀
T
amb
Ambient temperature
-30
85
癈
Table 4. Electrical Characteristics ADR Input
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
IH
High level input voltage
0.7 * VDD
VDD
V
V
IL
Low level input voltage
0
0.3 * VDD
V
I
LEAK
Input leakage current
-1
1
糀
Table 5. Electrical Characteristics I睠
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
IL
LOW-level input voltage
-0.5
0.3 * VDD
V
V
IH
HIGH-level input voltage
0.7 * VDD
VDD +0.5V
V
V
hys
Hysteresis of Schmitt Trigger inputs
VDD > 2.5V
0.05 * VDD
V
V
OL
LOW-level output voltage (open-drain
or open-collector) at 3mA sink current
VDD > 2.5V
0.4V
V
I
OL
LOW-level output current
VOL = 0.4V
20
mA
t
of
Output fall time from V
IHmax
to V
ILmax
120
1
1. In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors are used this has to be consid-
ered for bus timing.
ns
t
SP
Pulse width of spikes that must be
suppressed by the input filter
50
2
2. Input filters on the SDA and SCL inputs suppress noise spikes of less than 50 ns.
ns
I
i
Input current at each I/O pin
-10
+10
3
3. I/O pins of Fast-mode and Fast-mode plus devices must not obstruct the SDA and SCL lines if VDD is switched off.
糀
C
B
Total capacitive load for each bus line
550
pF
C
I/O
I/O capacitance (SDA, SCL)
4
4. Special purpose devices such as multiplexers and switches may exceed this capacitance due to the fact that they connect multiple
paths together.
Note: Operating conditions: T
amb
= -30癈 to +85癈, VDD = 2.5V to 3.6V (3V operation) unless otherwise noted.
10
pF
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATS137-PL-B-B
IC HALL SENSOR SGL 25MA SIP-3L
ATS177-PG-B-B
IC HALL SENSOR LATCH 25MA SIP-3L
ATS617LSGTN-T
IC HALL EFFECT GEAR SENSOR 4SIP
ATS625LSGTN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS627LSGTN-T
IC HALL EFFECT GEAR SENSOR 4-SIP
ATS635LSETN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS643LSHTN-I2-T
IC SENSOR GEAR TOOTH 4-SIP
ATS645LSHTN-I1
IC SENSOR GEAR TOOTH 4-SIP
相关代理商/技术参数
AS5510-DWLT-1K
功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5510-SO_EK_AB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:2.5 V ~ 3.6 V 嵌入式:- 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS5510-WL_EK_AB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:2.5 V ~ 3.6 V 嵌入式:- 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS5510-WL_EK_DB
功能描述:AS5510 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5510 标准包装:1
AS55110FLF
制造商:TT Electronics / IRC 功能描述:AS55110FLF
AS55110HLF
制造商:TT Electronics / IRC 功能描述:AS55110HLF
AS55110JLF
制造商:TT Electronics / IRC 功能描述:AS55110JLF
AS55111FLF
制造商:TT Electronics / IRC 功能描述:AS55111FLF
